Mặt Bích​ Ren ANSI B16.5 Threaded Flange

Mặt Bích​ Ren ANSI B16.5 Threaded Flange

Mặt Bích Ren ANSI B16.5 Threaded Flange Class 150/300/600

Mặt Bích Ren ANSI B16.5 Threaded Flange Class 150/300/600 là loại mặt bích theo tiêu chuẩn của Hoa Kỳ sử dụng trong kết nối đường ống, van, máy bơm... trong hệ thống dẫn lưu chất trong các ngành công nghiệp chủ lực, áp lực cao.

ANSI, ASME, ASA, B16.5 THREADED FLANGE
Quy Cách:
 3/8" (DN10) đến 40" (DN1000)
Áp suất làm việc: Class 150/300/600
Vật Liệu: Thép carbon (SS400, A105), Thép không gỉ Inox ( SS304. SS316)
Xuất Xứ: Hàn Quốc, Đài Loan, Vietnam, China,etc.
Kho Hàng: còn hàng
Mô tả sản phẩm: Theo tiêu chuẩn ANSI B16.5
Sử dụng: Năng lượng điện, dầu khí, khí tự nhiên, hóa chất, đóng tầu, thiết bị nhiệt, làm giấy, hệ thống cấp thoát nước, đường ống pccc, ngành công nghiệp, thực phẩm, đóng tàu, và hệ thống lạnh,vv

Jinan Hyupshin Flanges Co., Ltd, Manufacturer, ANSI B16.5 Threaded flanges, 150lbs, 300lbs, 600lbs

Dimensions & Masses of ANSI B16.5 Threaded Flange Class 150

Mặt Bích​ Ren ANSI B16.5 Threaded Flange


NOTE:
1. The thread conforms to ASME B1.20.1 NTP threads as described in Section 10. (The only exceptions are small male and female plain face threaded flanges which use NPSL recount threads.)
2. Class 150 threaded flanges are made without a counterbore. Threads are chamfered to the major diameter (approx.) at an angle of 45° (approx.) at the back of the flange.
3. Weights are based on manufacturer's data and are approximate.
4. For tolerances +-0.5mm.

Dimensions & Masses of ANSI B16.5 Threaded Flange Class 300
Mặt Bích​ Ren ANSI B16.5 Threaded Flange Class 300


NOTE:
1. Class 300 flanges except Lap Joint will be funished with 0.06 (1.6mm) raised face, which is included in ‘Thickness’ (C) and ‘Length through Hub’ (Y1), (Y3).
2. For Slip-on, Threaded, Socket Welding and Lap Joint Flanges, the hubs can be shaped either vertical from base to top or tapered within the limits of 7 degrees.
3. Blind Flanges may be made with the same hub as that used for Slip-on Flanges or without hub.
4. The gasket surface and backside (bearing surface for bolting) are made parallel within 1 degree. To accomplish parallelism, spot facing is carried out according to MSS SP-9, without reducing thickness (C).
5. Depth of Socket (D) is covered by ANSI B 16.5 only in sizes through 3 inch, over 3 inch is at the manufacturer’s option.

Dimensions & Masses of ANSI B16.5 Threaded Flange Class 600
Mặt Bích​ Ren ANSI B16.5 Threaded Flange Class 600


NOTE:
1. Class 600 flanges except Lap Joint will be funished with 0.06 (1.6mm) raised face, which is included in ‘Thickness’ (C) and ‘Length through Hub’ (Y1), (Y3).
2. For Slip-on, Threaded, Socket Welding and Lap Joint Flanges, the hubs can be shaped either vertical from base to top or tapered within the limits of 7 degrees.
3. Blind Flanges may be made with the same hub as that used for Slip-on Flanges or without hub.
4. The gasket surface and backside (bearing surface for bolting) are made parallel within 1 degree. To accomplish parallelism, spot facing is carried out according to MSS SP-9, without reducing thickness (C).
5. Depth of Socket (D) is covered by ANSI B 16.5 only in sizes through 3 inch, over 3 inch is at the manufacturer’s option.

Related product